Conference Program

Celle Drilling 2017, 11-12 September at Congress Union Celle


Monday, 11 September

11:30 - 13:00 | Registration
13:00 - 13:10 | Welcome
  • Thor Noevig, Chairman GeoEnergy Celle e.V.
13:10 - 13:30 | Program Introduction / Conference Overview
  • Prof. Dr.-Ing. Joachim Oppelt
13:30 - 14:00 | Keynote Talk
  • Inventing smarter ways to bring energy to the world
  • Tom Thissen, Baker Hughes, a GE company
14:00 - 14:30 | Keynote Talk
  • Big Data... Big Whoop! Is better the enemy of good enough?
  • Frank Springett, National Oilwell Varco
14:30 - 15:00 | Keynote Talk
  • Innovative design and operation of high-temperature geothermal wells.
  • Ingólfur Thorbjörnsson, ÍSOR - Iceland GeoSurvey | Project Consortium GeoWell
15:00 - 15:30 | Coffee Break & Networking
 
15:30 - 17:30

Session 1 “Drilling Equipment and Technology“

Session Chairs: Dirk Koch, Jürgen Schamp

  • New Laboratory Test Setup Enables Testing of Full Scale BHAs with Respect to Torsional Field Loads
    Dennis Heinisch, Baker Hughes, a GE company
  • Field test of simultaneous gyro attitude reference for magnetic ranging measurements in a near vertical magnetically perturbed environment
    Georgy Rassadkin, Scientific Drilling International USA
  • Composite Drill Pipe for Superior Performance
    Jaromir Ufer, Voith Composites GmbH & Co. KG
  • Optimised Hybrid Drill Bit Technology Matched to Application Yields Breakthrough in Drilling Performance
    Waleed Agawani, Baker Hughes, a GE company
  • (ePoster) Condition Monitoring
    Vincent von Melle, Zeppelin Power Systems
 

Tuesday, 12 September

07:30 - 08:30 | Registration, Coffee & Networking
 
08:30 - 10:30

Session 2 “Drilling Optimization and Dynamics I”

Session Chairs: Georg-Peter Ostermeyer, Bernd Schmalhorst

  • Field Test Result with a Stick-Slip Reduction Tool
    Steve Jones, Sanvean Technologies / Scout Downhole
  • 3D Directional Trajectory Prediction Using Coupled Bit and BHA models: Theory and Field Case Studies
    Will Attridge, Baker Hughes, a GE company
  • Case Study: Methods for Automated Drilling Performance Analysis Based on Downhole Measurements
    Hamza Sellami, Leibniz Universität Hannover Institute of Dynamics and Vibration Research (IDS)
  • Advanced Dynamics FEA Modelling as a New Approach for Geothermal Drilling Optimization in Indonesia
    Yoan Mardiana, Schlumberger
 

Session 3 “Drilling Fluids and Borehole Hydraulics”

Session Chairs: Udo Großmann, Roger Aragall

  • Simulation Of Steady State Cuttings Transport In Inclined And Horizontal Wells
    Yaroslav Ignatenko, Baker Hughes
  • An insight into the new IWCF Level 5 curriculum
    Ivo Nijhuis, The Well Academy BV
  • Flow-loop experiments with non-Newtonian reference fluids for estimating uncertainty of in-line rheology sensors
    Fionn Iversen, IRIS - International Research Institute of Stavanger
  • Drilling Fluids and Borehole Hydraulics
    James Mansell, Clear Solutions International Ltd
  • (ePoster) Sepiolite base mud challenges Harsh drilling conditions
    Ali Ettehadi, Izmir Katip Celebi University
 

GeoWell Part 1

Session Chair: Árni Ragnarsson

  • Chemical and microstructural alterations of annular cements of a high-temperature geothermal well
    Penny Pipilikaki, TNO - Netherlands Organisation for Applied Scientific Research
  • High-temperature composite casings
    Emile Lautier, Akiet
  • Flexible coupling of casings
    Gunnar Skúlason Kaldal, ÍSOR - Iceland GeoSurvey
  • Properties and selection of casing materials
    Ingólfur Thorbjörnsson, ÍSOR - Iceland GeoSurvey
 
10:30 - 11:00 | Coffee Break, Networking & e-Posters
 
11:00 - 12:30

Session 4 “Drilling Optimization and Dynamics II”

Session Chairs: Gerald Heisig, Gerhard Thonhauser

  • Drilling Systems Design and Operation Management: Leveraging the Value of Advanced Data-Driven Analytics
    Opeyemi Bello, TU Clausthal - Institute of Petroleum Engineering
  • Enhancing Post-Run Drilling Optimization with Data Analytics and High-Speed Drilling Dynamics Measurements
    Pedro Arevalo, Baker Hughes, a GE Company
  • Mathematical Modelling of Axial Vibration on Tri-Cone Bits for Maximum ROP and Optimum RPM
    Arash Asgharzadeh, TU Clausthal - Institute of Petroleum Engineering
  • (ePoster) Prediction of Bit and Reamer Loads for Increased Reliability of Hole-Opening BHAs
    Armin Kueck, Baker Hughes, a GE Company
 

Session 5 “Cementing, Well Integrity, Geomechanics”

Session Chairs: Christian Kiesl, Michael Röhrlich

  • Class G Cement – A Universal Remedy?
    Oliver Czuprat, DEA Deutsche Erdoel AG
  • Initial integrity evaluation of storage and production wells
    Thomas Brückner, Deep Underground Engineering
  • Innovative Casing Drilling Technology Improved The Ability to Set The Casing Deeper Through The Problematic Zone in Indonesia Geothermal Operation
    Bonar Noviasta, Schlumberger
  • (ePoster) Surface Deformation Study for a Geothermal Operation Field
    Julia Diessl, GeoMechanics Technologies
 

GeoWell Part 2

Session Chair: Árni Ragnarsson

  • Integrity monitoring of high temperature geothermal wells using fibre optic distributed sensing techniques
    Martin Lipus, GFZ German Research Centre for Geosciences
  • Development of a framework for well integrity risk assessment of geothermal wells
    Mohammad Mansouri Majoumerd, IRIS - International Research Institute of Stavanger
  • First result of DESCRAMBLE project: Drilling toward deep supercritical fluid?
    Massimo Luchini, EGP - Enel Green Power
 
12:30 - 13:30 | Lunch Break, Networking & ePosters
 
13:30 - 15:00

Session 6 “Drilling Simulation and Automation”

Session Chairs: Junichi Sugiura, Faissal Boulakhrif

  • Web Enabled High Fidelity Drilling Computer Model with User-Friendly Interface for Education, Research and Innovation.
    Robert Ewald, IRIS - International Research Institute of Stavanger
  • Miniature robotic drilling rig for research, technology development and education.
    Astrid Lescoeur, Martin Aagaard Olsen, Mayuran Vasantharanjan, Norwegian University of Science and Technology
  • Construction of an autonomous laboratory scale-drilling rig for testing and control of drilling systems
    Erik Løken, University of Stavanger
 

Session 7 “Hammer Drilling ”

Session Chairs: Michael Koppe, Matthias Reich

  • New developments for hard rock drilling - From hydraulic DTH Hammer to Laser Drilling
    Volker Wittig, International Geothermal Centre
  • The Water Hammer Effect in Hammer Drilling
    Marc Spinneker, TU Clausthal - Institute of Petroleum Engineering
  • HAMMR Drilling Motor Improves Efficiency
    Gunther von Gynz-Rekowski, ASHMIC LC
 

GeoWell Part 3

Session Chair: Árni Ragnarsson

  • Brief over view of the Icelandic deep drilling RN-15/IDDP-2 at Reykjanes, Iceland
    Ómar Sigurdsson, HS Orka
  • Well Integrity Platform
    Kris Ravi, Kris-Ravi Consultancy LLC
  • Discussion between the session participants on the GeoWell project
 
15:00 - 15:15 | Networking Break and Exhibition / ePoster
15:30 | Visit of Research Lab Drilling Simulator Celle
   (only for registered participants)
17:00 | End of Conference
   (Return to Congress Union Celle)

Gold Sponsor

 

Baker Hughes

 

Silver Sponsor

Schlumberger

ZEPPELIN Power Systems CAT

 

Sponsor

 

ExxonMobil

Wintershall

 

 

Download
Program Overview (PDF)
Program Overview (ZIP)

Organized by

GeoEnergy Celle e.V.

Endorsing Partners

International Association of Drilling Contractors (IADC) The Society of Petroleum Engineers Deutsche Wissenschaftliche Gesellschaft für Erdöl, Erdgas und Kohle  e.V. GtV - Bundesverband Geothermie Akademie für Geowissenschaften und Geotechnologien e.V. Energie-Forschungszentrum Niedersachsen Bundesverband Erdgas, Erdöl und Geoenergie e.V. Bundesverband Erdgas, Erdöl und Geoenergie e.V.